В галерее представлены файлы учебных моделей и приложений COMSOL Multiphysics® для решения электротехнических, механических, акустических, гидродинамических, тепловых и химических задач. Используйте эти примеры как отправную точку в ваших собственных исследованиях, скачивайте учебные модели, демонстрационные приложения и подробные описания к ним. Чтобы найти модели и приложения, относящиеся к сфере ваших интересов, воспользуйтесь функцией быстрого поиска. Обращаем внимание, что большую часть этих примеров можно также найти во встроенной в COMSOL Multiphysics® библиотеке приложений Application Libraries. Открыть библиотеку приложений можно через меню File.

Bracket — Structural Mechanics Tutorials

The bracket models are used as an introduction to structural mechanics modeling with the Structural Mechanics Module. The following features are introduced: The fundamentals: static linear analysis Parametric study Including initial strain Modeling thermal expansion Adding a rigid ... Читать дальше

Flow Past a Cylinder

The following model examines unsteady, incompressible flow past a long cylinder placed in a channel at right angle to the oncoming fluid. The cylinder is offset somewhat from the center of the flow to make the steady-state symmetrical flow unstable. The simulation time necessary for a ... Читать дальше

Laser Heating of a Silicon Wafer

A silicon wafer is heated up by a laser that moves radially in and out over time. In addition, the wafer itself is rotated on its stage. The incident heat flux from the laser is modeled as a spatially distributed heat source on the surface. The transient thermal response of the wafer is ... Читать дальше

Cable Tutorial Series

In this set of eight tutorial models and associated documentation, you can investigate the resistive, capacitive, inductive, and thermal properties of a standard three-core lead-sheathed XLPE HVAC submarine cable with twisted magnetic armor (500 mm2, 220 kV). The series includes a 2D, 2D ... Читать дальше

Cavity Flow Noise

Flow over a cavity and the tonal noise generated is a typical flow noise source in piping systems that have valves and other cavities. This tutorial model represents a simple case of cavity flow noise in a ducted system. The model is set up based on an example from Lafon et al. The ... Читать дальше

Heat Sink

This model is intended as a first introduction to simulations of fluid flow and conjugate heat transfer. It shows you how to: Draw an air box around a device in order to model convective cooling in this box, set a total heat flux on a boundary using automatic area computation, and ... Читать дальше

Heat Transfer by Free Convection

This example describes an array of heating tubes submerged in a vessel with fluid flow entering at the bottom. This is a multiphysics model because it involves fluid dynamics coupled with heat transfer. The pressure and the velocity field are the solution of the Navier-Stokes equations, ... Читать дальше

E-Core Transformer

This is the transient model of a single phase E-core transformer using a Multi-Turn Coil Domain. The model includes the effect of a nonlinear B-H curve in the core and shows how to connect the transformer model to the external circuits using Electric Circuit interface. The simulation is ... Читать дальше

Two-Phase Flow with Fluid-Structure Interaction

The following example demonstrates techniques for modeling a fluid-structure interaction containing two fluid phases in COMSOL Multiphysics. It illustrates how a heavier fluid can induce movement in an obstacle using the arbitrary Lagrangian-Eulerian (ALE) technique along with the Two ... Читать дальше

Permanent Magnet

As an example of a magnetostatic problem, consider how to model a horseshoe-shaped permanent magnet. One way is to treat the entire magnet as a ferromagnetic material, where the two end sections are defined as being pre-magnetized in different and opposite directions. Читать дальше

Первая
Назад
1–10 of 1653