A. K. Namdeo , H. B. Nemade ,
 Department of Electronics and Electrical Engineering, Indian Institute of Technology Guwahati, Guwahati, Assam, India
The paper presents a method of extraction of electrical equivalent circuit of a one port surface acoustic wave (SAW) resonator from the results of simulation based on finite element method (FEM) using COMSOL Multiphysics software. A one port SAW resonator consists of large number of periodic interdigital transducer (IDT) electrodes fabricated on the surface of a piezoelectric substrate. A ...
Quantum Mechanics Applications Using the Time Dependent Schrödinger Equation in COMSOL Multiphysics® Software
A. J. Kalinowski ,
 University of Connecticut, East Lyme, CT, USA
The paper illustrates the use of COMSOL for obtaining the quantum mechanics wave function Ψ(x,y,z,t) as a solution to the time dependent Schrödinger equation. Once having Ψ(x,y,z,t), it can be used to compute the probability of a particle being in a specific zone within the spatial field under consideration. Two problems are solved to illustrate solving Schrödinger's equation. Firstly, a simple ...
D. Chandler, J. Freels, R. Primm III, and G. Maldonado
Department of Nuclear Engineering, University of Tennessee, Knoxville, TN
Research Reactors Division, Oak Ridge National Laboratory, Oak Ridge, TN
Primm Consulting, LLC., Knoxville, TN
The computational ability to accurately predict the dynamic behavior of a nuclear reactor core in response to reactivity-induced perturbations is an important subject in reactor physics. Space-time and point kinetics methodologies were developed for the purpose of studying the transient-induced behavior of the High Flux Isotope Reactor’s (HFIR) compact core. The space-time simulations employed ...
M. Nour , A. Lakhssassi , E. Kengne , M. Bougataya ,
 Université du Québec en Outaouais, Gatineau, QC, Canada
Abstract: Due to the restriction of the number of probes that a patient can tolerate, and the inaccurate information provided by the invasive temperature measurements, which provide information only at discrete points, a mathematical model simulation is more effective to help doctors in planning their thermal treatment doses. This will maximize therapeutic effects while minimizing side effects. ...
Prof. Dr.-Ing. habil. A. K. Palit ,
 ZF-Lemfoerder Electronic GmbH, ZF-Friedrichshafen AG. Group, Espelkamp, Germany
Introduction: RFID system uses a Transponder and the near field communication (NFC) antenna and a matching circuit (Figure-1) in which at least latter two must be optimally designed for a higher efficiency. Typically, RFID antennas are flat inductive coils with 2 to 4 turns and are printed directly on the PCB. The larger antenna size implies larger operating distance whereas, the number of ...
R. W. Pryor
Pryor Knowledge Systems, Inc., Bloomfield Hills, MI, USA
The conductivity of seawater directly correlates with the concentration of dissolved salts. This model demonstrates a new approach to the methodology of inductive conductivity measurement of seawater and other liquids. COMSOL Multiphysics® was used to build a parametrically swept model of an O-Core Inductive Conductivity Measurement Sensor for Seawater. This sensor model is built using the ...
P. S. Rao, C. K. Chandra
Agricultural and Food Engineering Department, Indian Institute of Technology Kharagpur, West Bengal, India
High Pressure Processing (HPP) is a leading non-thermal food processing technology that is often cited as a major technological innovation in food preservation. Although it is very early to place this emerging technology among the list of breakthroughs in food processing, HPP has started to become a viable commercial alternative for pasteurisation of value added fruits, vegetables, meat, and ...
COMSOL Multiphysics® Simulations of Cracking in Point Loaded Masonry with Randomly Distributed Material Properties
A.T. Vermeltfoort, A.W.M. van Schijndel
Eindhoven University of Technology, Eindhoven, The Netherlands
This paper describes COMSOL Multiphysics® simulations of the stress and crack development in the area where a masonry wall supports a floor. In these simulations one of the main material properties of calcium silicate, its E-value, was assigned randomly to the finite elements of the modeled specimen. Calcium silicate is a frequently used building material with a relatively brittle fracture ...
U. Vogel , M. Spindler , S. Wege , T. Gemming 
 Leibniz Institute for Solid State and Materials, Dresden, Germany
In this work, we seek to simulate SAWs for a better understanding and to benchmark the currently available cloud computing possibilities of COMSOL Multiphysics® software. By using the MEMS module we demonstrate 3D models with reduced geometry to achieve principle information about the wavefield. For a benchmark, a high-speed workstation with limited memory (RAM) is compared to the most potent ...
A. Marchidan, T. Sullivan, J. Palladino
Trinity College, Hartford, CT, USA
COMSOL Multiphysics was used to design a binocular load cell. A three-dimensional linear solid model of the load cell spring element was studied to quantify the high-strain regions under loading conditions. The load cell was fabricated from 6061 aluminum, and general purpose Constantin alloy strain gages were installed at the four high-strain regions of the spring element. The four gages were ...