See How Multiphysics Simulation Is Used in Research and Development


Здесь представлены презентации, которые демонстрировались на конференциях COMSOL по всему миру. В презентациях рассказывается о передовых исследованиях и инновационных продуктах, созданных с помощью COMSOL Multiphysics. Исследования относятся к различным отраслям и областям применения, включая электрические, механические, гидродинамические и химические дисциплины. Чтобы найти презентации из нужной области, воспользуйтесь функцией быстрого поиска.
View the COMSOL Conference 2018 Collection
Heat Transfer and Phase Changex

Analysis of Burning Candle

J.S. Crompton, L.T. Gritter, S.Y. Yushanov, and K.C. Koppenhoefer
AltaSim Technologies LLC, Columbus, OH, USA

Analysis of burning candles is extremely complex; combustion produces a highly non-linear temperature profile through the flame in which local temperatures may exceed 1400 °C. Heat transfer includes radiation, conduction and convection components and the low melting point of the candle ... Читать дальше

Simulation and Design of an Oven for PET Blow Molding Machines

M. Mor[1], C. Seneci[1], V. Zacché[1], C. Remino[1], G. Petrogalli[1], D. Fausti[1]
[1]Polibrixia, Brescia, Italy

This paper presents the study and design of a new generation oven for PET blow-molding machines. The design faced several technical challenges such as: the temperature distribution in the critical areas, the sharp curvature radius, the high PET thermal inertia and the presence of ... Читать дальше

Heat Transfer and Phase Change Simulation in COMSOL Multiphysics® Software

N. Huc [1]
[1] COMSOL France, Grenoble, France

This session is devoted to phase change modeling in heat transfer simulations. The great interest in phase change comes from the outstanding thermal performance that it enables in particular for cooling or thermal protection applications. Alternatively, phase change can induce most of ... Читать дальше

Heat Transfer Modeling and Analysis of a Rotary Regenerative Air Pre-heater

R. K. Krishna, R. Ramachandran, and P. Srinivasan
Birla Institute of Technology and Science
Pilani
Rajasthan, India

An attempt has been made to sustain the efficiency of an air pre-heater(APH) in the long run. The APH is modeled using COMSOL Multiphysics in 3D and fed with real life conditions. Upon Heat transfer analysis, the temperature profile was found out and from that, the regions undergoing ... Читать дальше

Surface to Surface Radiation Benchmarks

J. v. Schijndel [1], R. v. Eck [1], M. Klep [1],
[1] Eindhoven University of Technology, Eindhoven, Netherlands

The paper presents a student guide on how to implement surface to surface radiation within COMSOL Multiphysics® software for case studies found within the built environment. We included four benchmarks: (1) Radiation in a triangular cavity with infinite length; (2) Radiation between two ... Читать дальше

Heat Generation Modeling of Two Lithium Batteries: from the Cell to the Pack in COMSOL Multiphysics® Software

J. Stoudmann [1], R. Rozsnyo [1], T. Mackin [2], J. Dunning [2]
[1] Haute École du paysage, d'ingénierie et d'architecture, Genève, Switzerland
[2] California Polytechnic State University, San Luis Obispo, CA, USA

A thermal model to predict the heat generation during the charge and discharge of a battery pack is an essential tool to manage the thermal behavior, performance and life of the batteries. In this work, a battery cell is modeled in COMSOL Multiphysics® using the Batteries and Fuel Cells ... Читать дальше

Process Modeling and Optimization of Design Parameters in a Falling Film Plate and Frame Evaporator

A. Donaldson [1], A. Thimmaiah [2],
[1] Dalhousie University, Halifax, Nova Scotia, Canada
[2] National Institute of Technology Karnataka, Mangalore, Karnataka, India.

COMSOL Multiphysics® software is used to explore the impact of distributor width on the film thickness, and the resulting sensitivity of overall thermal efficiency in a plate and frame triple-effect evaporator. A stable film is crucial to maintain a minimum wetting rate, to circumvent ... Читать дальше

Simulation of the Temperature Profile During Welding with COMSOL Multiphysics® Software Using Rosenthal's Approach new

A. Lecoanet[1], D. G. Ivey[1], H. Henein[1]
[1]Department of Chemical & Materials Engineering, University of Alberta, Edmonton, AB, Canada

A 3D finite element analysis is carried out, using COMSOL® software, to reproduce the thermal profile obtained with Rosenthal’s equation. The implemented heat transfer equation has been modified as a means to approximate Rosenthal’s solution. An analysis of the differences between the ... Читать дальше

Thermo-fluiddynamic Modeling of Laser Beam-Matter Interaction in Selective Laser Melting

K.-H. Leitz [1], P. Singer [1], A. Plankensteiner [1], B. Tabernig [1], H. Kestler [1], L. S. Sigl [1],
[1] Plansee SE, Reutte, Austria

Selective Laser Melting (SLM) offers great potential for future manufacturing technology. In order to extend its applicability for the processing of high melting materials like molybdenum fundamental process understanding is required. This can be obtained by multiphysical simulations ... Читать дальше

Glass Transition of ABS in 3D Printing

M. Rahman [1], N. R. Schott [2], L. K. Sadhu [3],
[1] North South University, Dhaka, Bangladesh
[2] Department of Plastics Engineering, University of Massachusetts - Lowell, Lowell, MA, USA
[3] IRays Teknology Ltd., Dhaka, Bangladesh

In a commercial 3D printer head, plastic ribbon passes through a hot nozzle of an extruder to dispense liquid plastic droplets to construct the model. In this paper a 2D axisymmetric model of a 3D head is considered to study the secondary transition change from below the glass ... Читать дальше

First
Назад
1–10 of 788